論文 - 今井　宏明

Enhanced and stabilized photoluminescence of perovskite cesium lead bromide nanocubes through ordered assemblies

Sasaki M., Hashimoto S., Iso Y., Oaki Y., Isobe T., Imai H.

Nanoscale Advances （Nanoscale Advances）  5 （ 9 ） 2553 - 2557 2023年04月

　概要を見る

This work clarified the effects of self-assembly of perovskite cesium lead bromide (CsPbBr3) nanocubes (NCs) covered with didodecyldimethyl ammonium bromide (DDAB) on photoluminescence (PL) properties. Although the PL intensity of isolated NCs was weakened in the solid state even under inert conditions, the quantum yield of PL (PLQY) and the photostability of DDAB-covered NCs were drastically improved by the formation of two-dimensional (2D) ordered arrays on a substrate. The PLQY of the 2D arrays increased to ca. 60% by initial excitation illumination at 468 nm and was maintained for over 4000 h. The improved PL properties are attributable to the fixation of the surface ligand around the NCs in the specific ordered arrays.

• Access to Document (DOI)

Construction of Millimeter-Wide Monolayers of Ordered Nanocubes as a Stain of “Wineglass Tears” Driven by the Marangoni Flow

Takatsuji Y., Matsumoto R., Sazaki G., Oaki Y., Imai H.

Langmuir （Langmuir）  39 （ 11 ） 4091 - 4099 2023年03月

ISSN  07437463

　概要を見る

We constructed millimeter-wide monolayers consisting of tetragonally ordered BaTiO3 (BT) nanocubes through the liquid film formation caused by the Marangoni flow in a toluene-hexane binary liquid containing oleic acid. A thin liquid film containing BT nanocubes was overspread on a standing silicon substrate through the condensation of toluene at the advancing front after the preferential evaporation of hexane. Then, the oscillatory droplet formation like “wineglass tears” occurred on the substrate. Finally, two-dimensionally ordered BT nanocubes were observed as a stain of “wineglass tears” on the substrate after the liquid film receded through evaporation. The presence of a thin liquid film in the binary system is essential for the production of millimeter-wide monolayers on the substrate because multilayer deposition occurs without the formation of a thin liquid film in monocomponent systems. We improved the regularity of the ordered arrays of nanocubes by adjusting the liquid component and evaporation conditions.

• Access to Document (DOI)

Stimuli-Responsive Sponge for Imaging and Measuring Weak Compression Stresses

Ono N., Seishima R., Okabayashi K., Imai H., Fujii S., Oaki Y.

Advanced Science （Advanced Science）  10 （ 3 ）  2023年01月

　概要を見る

Imaging and measuring compression stresses secure a safe and healthy life. Compression stresses in kPa range are not easily detected by conventional mechanoresponsive materials because microscopic molecular motion of the chromophores is not induced by such weak stresses. Moreover, imaging of the stress distribution is not achieved so far. The present study shows a sponge device combining two stimuli-responsive materials, a capsule releasing interior liquid and color-changing polymer in responses to compression stress and chemical stimulus, respectively. The stimuli-responsive capsule is dispersed on a melamine sponge comprised of the fibers with coating the layered polydiacetylene (PDA). The application of weak compression stresses induces collapse of the capsules, outflow of the interior liquid, and subsequent irreversible color change of PDA. The cascading response in the sponge device colorimetrically enables imaging of the distribution and measuring the strength of the compression stresses in kPa range. Furthermore, the device demonstrates imaging and measuring unknown weak compression stresses applied by the irregular-shaped objects. A couple of clinical issues in surgical operation of intestine are studied using the stress-imaging sponge device. The device and its design strategy can be applied to stress imaging in a variety of fields.

• Access to Document (DOI)

Fabrication process development and basic evaluation of eggshell-based column packing material for reversed-phase preparative separation

Yoshii T., Sakama A., Kanamori K., Nakanishi K., Imai H., Citterio D., Hiruta Y.

Journal of Chromatography A （Journal of Chromatography A）  1688 2023年01月

ISSN  00219673

　概要を見る

Purification of basic drugs in reversed-phase mode is often difficult, mainly due to adsorption of positively charged compounds to the silica gel-based stationary phase. Since this adsorption can be suppressed under alkaline condition, columns with alkali-resistance are required. In addition, compounds with acid-sensitive structures are sometimes degraded during separation on silica gel-based columns which exhibit acidity due to their surface structure. We prepared an alkali-resistant reversed-phase packing material, Eggshell-PMAcO based on eggshells modified with an amphiphilic copolymer, poly(maleic acid-alt-1-octadecene) (PMAcO). The height equivalent to a theoretical plate (HETP) of the Eggshell-PMAcO column was improved by surface treatment with ammonium acetate buffer (900 mM, pH = 3.7), which is an inexpensive reagent, and the retention behavior for hydrophobic compounds was compared to a typical ODS column based on silica gel, resulting in sufficient selectivity of the eggshell-based column for hydrophobic compounds, as indicated by the ratio of retention factors of pentylbenzene and butylbenzene (Eggshell-PMAcO column: 1.55, ODS column: 1.65). Column temperature-dependent retention behavior of naphthalene was investigated in the temperature range from 25 °C to 45 °C, followed by the calculation of thermodynamic parameters. There was little difference in the standard molar enthalpy (Eggshell-PMAcO: −19.6 kJ/mol, ODS: −21.7 kJ/mol). The absolute value of the standard free Gibbs energy for the Eggshell-PMAcO column was much smaller than that of the ODS column (Eggshell-PMAcO: −0.284 kJ/mol, ODS: −13.0 kJ/mol), indicating that the Eggshell-PMAcO column had a weaker retention strength for naphthalene than the ODS column mainly due to the large difference in the standard molar entropy (Eggshell-PMAcO: −64.9 J/mol K, ODS column: −29.2 J/mol K). The retention capacities for imipramine under neutral (water/methanol) and alkaline (0.1% triethylamine water/methanol) conditions were 0.2 mg and 5 mg, respectively, based on injection mass-dependent HETP, retention factor and symmetry factor. Finally, the prepared column was applied to the purification of a building block for nucleic acid drugs. This study demonstrated that reversed-phase columns, which can be fabricated from eggshells and an amphiphilic copolymer in an inexpensive and eco-friendly way, have the ability to purify basic compounds and acid-sensitive compounds.

• Access to Document (DOI)

A highly sensitive friction-imaging device based on cascading stimuli responsiveness

Shioda N., Kobayashi R., Katsura S., Imai H., Fujii S., Oaki Y.

Materials Horizons （Materials Horizons）  2023年

ISSN  20516347

　概要を見る

Imaging and measurement of friction forces are required in a variety of fields. If the friction forces originating from the motions of professionals are quantitatively analyzed, the data can be applied to a motion-copying system by a robot. However, weak friction forces have not been visualized and quantified using conventional sensing materials and devices because of their low sensitivity. Here we present a highly sensitive friction-imaging device based on the cascading responses of stimuli-responsive materials, namely polydiacetylene (PDA) and dry liquid (DL). Weak friction forces disrupt the DL, which is composed of liquid droplets surrounded by solid particles. The outflowing liquid under chemical stress changes the color of PDA. The cascading responses enable colorimetric imaging and measurement of weak friction forces in the range of 0.006-0.080 N. Furthermore, the device visualizes the force distribution of handwriting in calligraphy depending on the individual characteristics of an expert, a practician, and a beginner. A high-sensitivity friction-imaging device can be used to understand various motions.

• Access to Document (DOI)

Micro- and nanometric characterization of the celestite skeleton of acantharian species (Radiolaria, Rhizaria)

Fujimaki R., Suzuki N., Kimoto K., Nagai Y., Oaki Y., Shimode S., Toyofuku T., Imai H.

Scientific Reports （Scientific Reports）  12 （ 1 ）  2022年12月

　概要を見る

We clarified the specific micrometric arrangement and nanometric structure of the radiolarian crystalline spines that are not a simple single crystal. A body of the celestite (SrSO4) skeleton of acantharian Acanthometra cf. multispina (Acanthometridae) composed of 20 radial spines having four blades was characterized using microfocus X-ray computed tomography. The regular arrangement of three types of spines was clarified with the connection of the blades around the root of each spine. The surface of the spines was covered with a chitin-based organic membrane to prevent from dissolution in seawater. In the nanometric scale, the mesocrystalline structure that consists of nanoscale grains having distorted single-crystal nature was revealed using scanning- and transmission electron microscopies, electron diffraction, and Raman spectroscopy. The acantharian skeletons have a crystallographically controlled architecture that is covered with a protective organic membrane. These facts are important for penetrating the nature of biogenic minerals.

• Access to Document (DOI)

Ultrastructure of setae of a planktonic diatom, Chaetoceros coarctatus

Owari Y., Nakamura F., Oaki Y., Tsuda H., Shimode S., Imai H.

Scientific Reports （Scientific Reports）  12 （ 1 ）  2022年12月

　概要を見る

Silica frustules of most planktonic diatoms have many shallow holes in which the length (L) is smaller than the width (W). The present study focuses on a silica ultrastructure of setae of a planktonic diatom having deep (L/W > 1) holes. Here, we characterized microscopically patterned nanoholes on the silica walls of thick, robust, and hollow setae of a colony of Chaetoceros coarctatus. Basically, tetragonal poroid arrangements with and without a costa pattern are observed on the inner and outer surfaces, respectively, for three kinds of curving hollow setae attached to the anterior, intercalary, and posterior parts of the colony. The seta structures including specific poroid arrangements and continuity of deep nanoholes depend on the location. The deep nanoholes ∼90 nm wide are elongated from 150 to 1500 nm (L/W ∼17) with an increase in the wall thickness of the polygonal tubes of the setae. The inside poroid array, with a period of 190 nm in the extension direction of setae, is lined by parallel plates of the costae. However, the poroid arrangement on the outer surface is disordered, with several holes obstructed with increasing wall thickness of the posterior terminal setae. According to the movement of a colony in a fluid microchannel, the thick curving terminal setae is suggested to involve attitude control and mechanical protection. Using an optical simulation, the patterned deep through-holes on the intercalary setae were suggested to contribute anti-reflection of blue light in the wavelength range of 400 to 500 nm for the promotion of photosynthesis in seawater.

• Access to Document (DOI)

Preparation of conductive Cu<inf>1.5</inf>Mn<inf>1.5</inf>O<inf>4</inf> and Mn<inf>3</inf>O<inf>4</inf> spinel mixture powders as positive active materials in rechargeable Mg batteries operative at room temperature

Takemitsu H., Hayashi Y., Watanabe H., Mandai T., Yagi S., Oaki Y., Imai H.

Journal of Sol-Gel Science and Technology （Journal of Sol-Gel Science and Technology）  104 （ 3 ） 635 - 646 2022年12月

ISSN  09280707

　概要を見る

We prepared conductive mixtures of Cu1.5Mn1.5O4 and Mn3O4 spinels (CMO–MOs) as positive electrode active materials in rechargeable Mg batteries (RMBs) using a sol–gel complex polymerization method. The CMO–MO spinel mixtures with high specific surface areas above 100 m2 g−1 were obtained with mild calcination in Ar at 300 °C. The conductivity of CMO–MOs was estimated to be approximately 1000 times higher than that of a conventional MgMn2O4 (MMO) spinel powder. The discharge capacities evaluated using 2032-type coin-cell battery with a Mg-alloy negative electrode at room temperature increase with an increase in the specific surface area of the spinel powders. The specific surface area for providing the theoretical capacity of the conductive CMO–MOs was about one-third that of the insulative MMO. High specific surface area and high conductivity are key parameters for the positive active material to realize practical room-temperature operation of RMBs.

• Access to Document (DOI)

Amphiphilic Copolymer-Modified Eggshell-Based Column Packing Materials for the Preparative Separation of Basic Drugs

Yoshii T., Mochida M., Kaizu K., Soda Y., Kanamori K., Nakanishi K., Sato T., Imai H., Citterio D., Hiruta Y.

ACS Applied Polymer Materials （ACS Applied Polymer Materials）  4 （ 10 ） 6949 - 6957 2022年10月

　概要を見る

A way to utilize eggshells is desired because most of the eggshell waste is disposed of in landfills. Despite eggshells having attractive features such as a thermodynamically stable porous crystalline structure, their effective utilization as a functional material has yet to be demonstrated. Herein, we developed an alkali-stable column packing material for reversed-phase preparative high-performance liquid chromatography (HPLC) based on eggshells. Nanocrystals and biopolymers present on eggshell powder were removed by surface treatment with buffered ethylenediaminetetraacetic acid (EDTA) and sodium hypochlorite solutions, resulting in bare calcium carbonate with a uniform porous surface. The obtained particles were modified with poly(maleic acid-alt-1-octadecene) (PMAcO) having hydrophobic alkyl chains and anionic carboxylate groups. The prepared PMAcO-modified eggshell-based material was applied to an HPLC column, and its performance is evaluated. The column succeeded in the separation of alkylbenzenes, steroids, and diastereomers. It was also used for the separation of basic tricyclic antidepressants in an alkaline mobile phase, showing excellent retention capacity and alkali stability. This study demonstrates the potential of eggshell utilization, providing not only a practical stationary phase for HPLC but also a solution for recycling calcium carbonate-based biomineral waste.

• Access to Document (DOI)

Coatable 2D Conjugated Polymers Containing Bulky Macromolecular Guests for Thermal Imaging

Edagawa A., Matsuda S., Kawakubo H., Imai H., Oaki Y.

ACS Applied Materials and Interfaces （ACS Applied Materials and Interfaces）  14 （ 38 ） 43792 - 43801 2022年09月

ISSN  19448244

　概要を見る

Dynamic properties are derived from the structural flexibility of 2D polymers. Softening layered structures has the potential for tuning and enhancing the dynamic properties. In the present work, the flexibility of layered polydiacetylene (PDA) is tuned by the interlayer polymeric guests with different branching structures. PDA shows thermoresponsive color-change properties through shortening the effective conjugation length with molecular motion. Whereas the blue-to-red color transition is observed at certain threshold temperatures for the layered PDA without the interlayer guest, the intercalation of the bulky polymer guests lowers the starting temperature and widens the temperature range for the thermoresponsive color changes. The resultant layered composite of PDA and bulky polymer affords the homogeneous coating on substrates on the centimeter scale. The thermoresponsive color-change coating is applied to temperature-distribution imaging. The specific heat of liquids is colorimetrically estimated using the coating on the bottle. The coating on a silk cloth visualizes the temperature distribution on a simulated tissue during surgical operation using an ultrasonic coagulation cutting device. The coating can be applied to thermal imaging in a variety of fields. Moreover, the softening strategy contributes to explore dynamic properties of soft 2D materials.

• Access to Document (DOI)

Selective syntheses of thick and thin nanosheets based on correlation between thickness and lateral-size distribution

Haraguchi Y., Imai H., Oaki Y.

iScience （iScience）  25 （ 9 ）  2022年09月

　概要を見る

Exfoliation of layered materials, a typical route to obtain 2D materials, is not easily controlled because of the unpredictable downsizing processes. In particular, the thickness control remains as a complex challenge. Here, we found a correlation between the thickness and lateral size distribution of the exfoliated nanosheets, such as transition metal oxides and graphene oxide. The layered composites of the host metal oxides and interlayer organic guests are delaminated into the surface-modified nanosheets in organic dispersion media. The exfoliation behavior varies by combination of the hosts, guests, and dispersion media. Here, we found that the thick and thin nanosheets were obtained on the monodispersed and polydispersed conditions, respectively. The selective syntheses of the thick and thin nanosheets were achieved using a prediction model of the lateral size distribution. The correlation between the thickness and lateral size distribution can be applied to thickness-selective syntheses of 2D materials.

• Access to Document (DOI)

Nanosheet-Based Uneven Thin Film Exhibiting Angle-Independent Structural Color and Its Application to Detection of Biogenic Amines

Haraguchi Y., Imai H., Oaki Y.

Advanced Materials Interfaces （Advanced Materials Interfaces）  9 （ 25 ）  2022年09月

　概要を見る

Anisotropic ultrathin 2D materials are used as building blocks to obtain higher-order structures. Tailoring the size, surface chemistry, and assembly state of exfoliated nanosheets is required for the design of functional materials. However, these factors are not easily controlled during the down-sizing exfoliation process, which is a general route for obtaining 2D materials. In the present work, polydispersed nanosheets of a transition metal oxide are prepared based on prediction model for the size distribution constructed by a combination of machine learning and chemical perspective on small data. Self-assembly of the exfoliated nanosheets results in the uneven thin films exhibiting an angle-independent structural color. As the nanosheets vary in thickness and lateral size, their assembled thin films exhibit structural color independent of the incident angle. The structural color is changed by casting only 20 µL of an aqueous solution containing biogenic amines such as histamine within a sensing time of 5 min. The biogenic amines are intercalated into the interlayer space of the stacked nanosheets and the resulting increase in the thickness changes the color of the thin-film device. The new design strategies can be applied to constructing other thin-film sensing devices based on nanosheets.

• Access to Document (DOI)

Quantitative evaluation of reversed-phase packing material based on calcium carbonate microspheres modified with an alternating copolymer

Kaizu K., Mochida M., Imai H., Citterio D., Hiruta Y.

Journal of Chromatography A （Journal of Chromatography A）  1677 2022年08月

ISSN  00219673

　概要を見る

Considering the vulnerability of silica gel to alkaline mobile phases, a highly alkaline stable stationary phase for HPLC is required to separate basic compounds with high separation efficiency. To address this issue, we have developed a high alkaline stable packing material (CaCO3-PMAcO) based on mesoporous calcium carbonate microspheres modified with poly(maleic acid-alt-1-octadecene). In this study, we report further investigation of the separation performance of CaCO3-PMAcO column by systematically evaluating the effects of particle size and chromatographic conditions. Based on the theory of the van Deemter equation, the separation efficiency was related to the size of CaCO3-PMAcO particles (2.9 – 5.7 µm). The evaluation of thermodynamics of retention by changing the column temperature from 20 °C to 45 °C implied that the retention mode was dominated by hydrophobic interaction associated with the exothermic enthalpy changes (-11.1 to -12.5 kJ/mol). The results of column selectivity tests revealed that the CaCO3-PMAcO column had hydrophobic selectivity comparable to C18 silica gel columns (αP/B; CaCO3-PMAcO column: 1.53, C18 column: 1.69), and higher shape/steric selectivity (αTri/Ter; CaCO3-PMAcO column: 1.56, C18 column: 0.955). In practice, the CaCO3-PMAcO column could be applied to the separation of not only alkylbenzenes and polycyclic aromatic hydrocarbons, but also to basic tricyclic antidepressants by using an alkaline mobile phase (pH 12).

• Access to Document (DOI)

A Capacity-Prediction Model for Exploration of Organic Anodes: Discovery of 5-Formylsalicylic Acid as a High-Performance Anode Active Material

Komura T., Sakano K., Igarashi Y., Numazawa H., Imai H., Oaki Y.

ACS Applied Energy Materials （ACS Applied Energy Materials）  5 （ 7 ） 8990 - 8998 2022年07月

　概要を見る

Development of high-performance organic energy storage is one of the important challenges in recent materials science. Molecular design and synthesis have potential for enhancement of the performances. Efficient exploration and design of the molecules are required in a wide search space. In the present work, a capacity prediction model for organic anodes was constructed on small experimental data by sparse modeling, a method of machine learning, combined with our chemical insights. The straightforward linear regression model facilitated discovery of a high-performance active material for organic anodes in a limited number of experiments. A recommended compound, 5-formylsalicylic acid (SA-CHO), showed one of the highest performances in recent works, i.e., a specific capacity of 873 mA h g-1at 100 mA g-1(sample number: n = 3) with rate performance and cycle stability. The model can be applied to explore organic anode active materials with higher specific capacity.

• Access to Document (DOI)

Demonstrated gradual evolution of disorder in crystalline structures between single crystal and polycrystal via chemical and physicochemical approaches

Kanazawa S., Oaki Y., Imai H.

CrystEngComm （CrystEngComm）  24 （ 25 ） 4546 - 4550 2022年06月

　概要を見る

Various biological and biomimetic minerals are composed of mesocrystals, in which nanoscale crystalline units are ordered in approximately the same crystallographic direction. However, the variation of the crystallographic regularity of mesocrystals has not been clarified using experimental evidence. This work demonstrated the gradual evolution of disorder in crystalline structures between single crystal and polycrystal by monitoring the crystallographic regularity using electron diffraction patterns. Single-crystal rods of fluorapatite elongated in the c direction are switched to mesocrystals consisting of iso-oriented nanorods by adding a specific molecule having a carboxy group (chemical approach) and to roughly arranged nanograins by increasing the degree of supersaturation at the growth front (physicochemical approach). Lateral and vertical miniaturization of the growth units is achieved through stepwise nucleation and near-epitaxial growth. The crystallographic regularity gradually decreases with deviation of the c axis and rotation of the a axes through reduction of the growth unit size. Here we can tune the disorder in crystalline structures via the chemical and physicochemical approaches.

• Access to Document (DOI)

A nonclassical pathway to biomimetic strained SrSO<inf>4</inf> crystals

Fujimaki R., Oaki Y., Imai H.

CrystEngComm （CrystEngComm）  24 （ 24 ） 4356 - 4360 2022年05月

　概要を見る

Biomimetic strained SrSO4 crystals were produced through a nonclassical pathway involving fiber-by-fiber accumulation with poly(acrylic acid) in an aqueous solution system. Polymer-stabilized fibrous hydrate crystals 20-40 nm wide and several micrometers long were formed in the initial stage. Spindle-shaped microrods of SrSO4 were then constructed by oriented attachment of the hydrous fibrils and subsequent dehydration. The strained structure of the anhydrous SrSO4 crystals is similar to biogenic SrSO4 spines of acantharian species, a marine unicellular holoplanktonic protist.

• Access to Document (DOI)

Performance Predictors for Organic Cathodes of Lithium-Ion Battery

Sakano K., Igarashi Y., Imai H., Miyakawa S., Saito T., Takayanagi Y., Nishiyama K., Oaki Y.

ACS Applied Energy Materials （ACS Applied Energy Materials）  5 （ 2 ） 2074 - 2082 2022年02月

　概要を見る

Organic cathodes for lithium-ion batteries are one of the most promising and significant materials toward a sustainable society. The molecular design is a key to achieve superior performances beyond inorganic cathodes. The present work shows predictors of the reaction potential, specific capacity, and ideal energy density for organic cathodes. Straightforward prediction models of the performance were constructed by a combination of machine learning and chemical insight, namely, sparse modeling for small data (SpM-S), on a small data set as training data found in the literature. The prediction accuracy was validated using different literature data. The predictors can be applied to explore high-performance organic cathodes in a wide search space efficiently. Moreover, SpM-S afforded straightforward, interpretable, and generalizable prediction models compared to other machine-learning algorithms. The small-data-driven methodology can be applied for further exploration of materials, enhancement of performances, and optimization of processes.

• Access to Document (DOI)

Designed nanostructures created via physicochemical switching of the growth mode between single crystals and mesocrystals†

Kanazawa S., Oaki Y., Imai H.

Nanoscale Advances （Nanoscale Advances）  4 （ 6 ） 1538 - 1544 2022年02月

　概要を見る

Most biominerals are composed of mesocrystals, in which individual nanoparticle building units have a defined long-range order on the atomic scale in at least one direction. Although the crystal size and orientation of the mesostructures are spatially designed in biological architectures, it has been difficult to achieve adequate control of the crystal growth to produce modulated mesostructures in artificial aqueous systems. Here, we propose a simple physicochemical approach for the spatial design of nanostructures using an aqueous solution system. The ordered arrays of oriented fluorapatite (FA) rods similar to tooth enamel are produced on a polymer substrate in a supersaturated solution. We succeeded in reversible switching of the growth mode of FA between single-crystalline rods and mesocrystalline grains through the disturbance of the solution. The primary crystal size was tuned between micrometric rods ∼0.5 μm wide and >5 μm long and nanoscale grains ∼10 nm wide and 50 nm long without a drastic change in the c direction. Hierarchical architectures consisting of iso-oriented FA microrods and nanograins were constructed via temporal control of the crystal growth mode by switching a physicochemical parameter, such as the degree of supersaturation at the growth front.

• Access to Document (DOI)

Electroless nickel plating on a biomineral-based sponge structure

Takeoka H., Seike M., Nakamura Y., Imai H., Oaki Y., Fujii S.

Materials Advances （Materials Advances）  3 （ 2 ） 931 - 936 2022年01月

　概要を見る

A 3-dimensional polypyrrole-palladium nanocomposite material was prepared by transferring a sponge structure of a sea urchin spine via chemical oxidative polymerization. The nanocomposite material was successfully coated with nickel, maintaining the 3-dimensional sponge structure by electroless plating in an aqueous medium.

• Access to Document (DOI)

Characterization of calcite spines of planktonic foraminifers (Globigerinidae)

Izumida K., Takasaki M., Fujimaki R., Nagai Y., Oaki Y., Naito K., Tanaka Y., Shimode S., Toyofuku T., Imai H.

CrystEngComm （CrystEngComm）  24 （ 13 ） 2446 - 2450 2022年

　概要を見る

Calcitic spines ∼1 μm in diameter are projecting from a trochospiral test of a spinose planktonic foraminifer. According to electron diffraction, Raman spectra, and detailed electron microscope observation, the spines were found to be a single-crystal-like calcite that has a nanogranular texture containing microstrain. An organic envelope protects the biogenic calcite against dissolution in water. Their unique mechanical and chemical properties are ascribed to the specific micro- and nanoscopic structures. This journal is

• Access to Document (DOI)